Ratoc Systems USB-Serial Converter REX-USB60F Manual de usuario Pagina 139
- Pagina / 250
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
6-21
6
Parameter description
6. Parameter description
Parameter
No.
Parameter
name
Setting range
[Default value]
Description
FA-86
Pole position
offset
* Valid only for
RDP.
8000 to 7FFF
[0]
Specifies the phase Z distance used as the reference
and zero crossing (rising) for the induced voltage
of phase U or across U and V. Set this parameter in
signed hexadecimal of 16-bit length. By quantizing
this setting, the 180° electrical angle of the linear
motor will be H'4000 (hexadecimal).
Use FA-88 to set the type of reference voltage (phase
voltage or line voltage).
FA-87
Linear scale
polarity
* Valid only for
RDP.
A, b
[b]
Sets the phase direction in the forward run of the
linear scale. Set this parameter to "b".
Setting
Phase
b Phase B leads phase A.
FA-88
Phase angle of
pole position
* Valid only for
RDP.
PHASE,
LinE
[PHASE]
Sets whether the phase of magnetic pole position
signal is the same as the phase voltage or line
voltage of the linear motor induced voltage. The
offset specified by parameter FA-86 is relative to this
parameter setting. Set this parameter to "PHASE".
Setting
Phase
PHASE
• Magnetic pole position signal has the
same phase as phase voltage.
• FA-86 is relative to the induced
voltage of phase U.
FA-89
Preset condition
for pole position
* Valid only for
RDP.
OrLP,
OrLn
[OrLP]
Sets the condition for presetting the magnetic pole
position. Set this parameter to "OrLP".
Setting
Preset condition
OrLP
Preset at the first phase Z position after
the ORL signal is switched from OFF to
ON.
FA-90
Hall sensor
connection
* Valid only for
RDP.
oFF,
CnCt,
oFF2
[oFF2]
Sets the sequence of magnetic pole position
estimation operation. Use this parameter by setting
to "oFF2".
Setting
Description
oFF2
Starts magnetic pole position estimation
only when the SON terminal is first
switched from OFF to ON after power-
on.
Note 1: When set to "oFF2", the RS terminal is
enabled only when resetting an alarm after it
has tripped.
FA-98
Initialization
mode selection
CH
dAtA
AbS
[CH]
Use this parameter to select whether to clear the
alarm/trip log or to initialize the user data. Do not set
this parameter to "AbS".
Setting
Description
CH
Clears the alarm/trip log.
Cancels the monitor of a specific
parameter (d-xx) that is automatically
displayed at power-on.
dAtA Initializes the user data.
- RD series 1
- General Contents 5
- 7.1.2 Daily inspection 7-2 8
- 7.1.3 Cleaning 7-2 8
- Chapter 1 Safety precautions 11
- 1.1 Precautions for use 13
- 1.2 Storage 14
- 1.3 Carrying 15
- 1.4 Installation 15
- 1.5 Wiring 16
- 1.6 Control and operation 17
- Safety precautions 18
- Before using the unit 21
- 2.1.1 Checking the product 21
- 2.1.2 User's manual 22
- 2.2.2 Warranty 23
- 3.1 Installation 29
- Installation and wiring 30
- 3.2 Wiring 32
- 3.2.2 Main circuit wiring 33
- (Collector) 50
- Chapter 4 Operation 57
- 4.1 Control and operation 59
- Operation 60
- 4.2 Test Run 61
- 4.3 Emergency stop 64
- Chapter 5 Functions 65
- 5.1 Terminal function list 67
- 5.2 Input terminal functions 69
- 5.7 Smoothing function 91
- Functions 100
- 5.11 Gain change function 101
- 5.13 Motor rotating direction 106
- 5.14 Speed limit function 107
- 5.16 Notch filter function 110
- No particular instructions 111
- Fd-01 (Fd-34) 113
- Contents 115
- Parameter description 119
- 6.2 Function lists 123
- 8000 to 7FFF 0 – No 126
- (Note 1) 128
- 6.3 Function description 130
- * Valid only for 139
- A-86 is relative to this 139
- (H/L) at return-to 140
- (Note 2) 144
- Maintenance and Inspection 207
- 7.1.2 Daily inspection 208
- 7.1.3 Cleaning 208
- 7.1.4 Periodic inspection 208
- 7.5 Capacitor life curve 212
- 8.1 Specification tables 215
- Specifi cations and Dimensions 216
- Chapter 9 Troubleshooting 221
- Troubleshooting 223
- 9.3 Troubleshooting 225
- Chapter 10 Appendix 235
- 10.1 Timing chart 237
- 10.2 Options 238
- Appendix 239
- Regenerate 249
- (Not provided 249
- 200W type) 249
Relacionado con productos y manuales para Redes Ratoc Systems USB-Serial Converter REX-USB60F
Redes Ratoc Systems CBFW3 Manual de instrucciones
(146 paginas)
(146 paginas)
Redes Ratoc Systems CBFW3 Guía de usuario
(90 paginas)
(90 paginas)
Redes Ratoc Systems CFU2 Guía de usuario
(16 paginas)
(16 paginas)
Redes Ratoc Systems CB31U Manual de usuario
(152 paginas)
(152 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales